
Think about the water bodies in your community — streams, rivers, lakes, maybe even bays and oceans. All of these provide a wide variety of important resources for daily life for people living in the community.
Reservoirs for drinking water supplies. Power capability for manufacturing plants and electrical power generation. Navigable channels for shipping and commerce. Recreational opportunities for swimming, fishing, boating, water sports, or scenic views. The list is endless!
However, these waterways wouldn’t be as valuable of a resource if they were polluted, right? Yet, according to the US Environmental Protection Agency’s (EPA) National Water Quality Report, presented to Congress in 2017, 46% of our nation’s waterways are classified as impaired waters due to pollution.
The Two Categories of Pollutants
Pollutants that enter a waterbody are classified into two main categories: point sources or nonpoint sources.
Point Sources include all sources subject to regulation under the National Pollutant Discharge Elimination System (NPDES) program. Wastewater treatment facilities, some stormwater discharges such as Municipal Separate Storm Sewer Systems (MS4) and Combined Sewer Systems (CSS), and concentrated animal feeding operations (CAFOs)…just to name a few.
The majority of point sources enter via a discharge pipe or specific geographic locations(s), hence their points of entry are easily identifiable.
Non-Point Sources, on the other hand, include all remaining sources of pollutants, as well as natural background sources such as stormwater runoff, septic systems, erosion and sediment, nutrients from lawn fertilizer and pet waste.
The specific locations of origin for these pollutants are typically spread over wide and multiple geographic areas within the watershed, hence they’re more difficult to pinpoint.
Water Quality Standards
The Clean Water Act (CWA), established by Congress in 1972, authorized the EPA to regulate water quality. One provision of the CWA was the requirement that all waters of the United States have water quality standards set to protect them.
To implement this, the CWA required that each state establish water quality standards for all bodies of water in the state and that each state monitor the pollutant levels in these water bodies.
Any waters not meeting the standard must be identified and specifically listed as not meeting the standard. This list is commonly referred to as the “303d List” because it’s specifically Section 303d of the Clean Water Act that requires this listing and identification.
States are required to submit their 303d List to EPA every two years for approval, and when known, must identify the pollutant and its source causing the impairment.
Furthermore, the Clean Water Act then requires that the states establish a TMDL for each pollutant in waters not meeting the standard.
What is a TMDL?
A TMDL stands for Total Maximum Daily Load, which is the calculation of the maximum amount of a pollutant allowed to enter a waterbody so that it’ll meet and continue to meet water quality standards for that particular pollutant.
A TMDL determines a pollutant reduction target and allocates load reductions necessary to the source(s) of the pollutant. This reduction is known as a waste load allocation (WLA), or simply a load allocation.
Basically each pollutant is assigned a maximum amount of that pollutant that can enter the watershed.
A TMDL must also account for seasonal variations in water quality, and include a margin of safety (MOS) to account for uncertainty in predicting the effectiveness of pollutant reductions in meeting water quality standards.
For example, if the pollutant is nitrogen or phosphorus, Water Resources and Environmental Engineers must account for seasonal variations in fertilizer use that contribute to these pollutants.
The main sources of these pollutants are applied in the spring and summer seasons, compared to the winter, hence the potential for these pollutants to enter the watershed to be higher in the spring and summer.
But fertilizing may not be the only source of these pollutants within the watershed. Each pollutant causing a waterbody to be impaired or threatened is referred to as a waterbody/pollutant combination, and typically a TMDL is developed for each waterbody/pollutant combination.
How Does It Appear on Your Exam?
TMDL’s and their associated concepts are a frequently asked question on the FE and PE exams, especially in the Water Resources discipline.
The PE Reference Handbook provides the following equation to calculate TMDLs, Waste Load Allocations, and determine appropriate Margins of Safety.
The equation is also helpful just for understanding how a TMDL is calculated.
It is important to understand that this equation allows you to calculate the TMDL in terms of a mass per day unit (mass/day). Maybe it’s pounds of phosphorus per day, or pounds of Total Suspended Solids (TSS) per day.
However, it is very likely that you will need to calculate the TMDL in terms of units of concentration, such as milligrams per liter (mg/L).
Our FE Review Course and PE Review Courses provide direct instruction on taking these concepts and calculations further, as well as applying TMDL calculations to actual FE and PE Exam problems!
Furthermore, TMDLs are a great topic for NCESS to test your knowledge with concept problems. The main question we get from our readers and students in our courses is how to ace concept problems, which are becoming increasingly popular on both the FE and PE exams!
More information on TMDLs can be found on the EPA’s website.
Conclusion
TMDLs are an important tool in protecting and improving water quality and regulating the discharge of pollutants from both point sources and nonpoint sources.
With the increasing focus on sustainability and environmental responsibility across all disciplines of engineering, no doubt TMDLs will continue to be a crucial topic in the world of civil engineering. And, of course, they are pretty likely to pop up on your FE or PE Exam!
All of us here at Civil Engineering Academy are here to help you every step of the way towards becoming a licensed PE — acing both the FE and PE Exams!
Civil Engineering Academy’s Breadth and Depth Courses were the keys to success on my own journey, and I invite you to check them out. We’ll see you there!
Author: Matt Fanghella, PE, CFM



